MOBILE THERMAL PRINTER
— 6 —● Do not dip battery in water or sea water. Wet battery may generateheat or may be subject to corrosion.● Do not use or leave battery at high te
— 7 —CAUTION● Print density may change with the kind of print paper. Printdensity is adjusted by the Print Density Set command inCommand Reference.
— 8 —WARNINGCAUTIONCAUTION● With one side of the connector connected to this product, do nottouch the metal part of the other connector.Precautions on
— 9 —THE TABLE OF CONTENTS1. INTRODUCTION ... 101.1 Features ...
— 10 —1. INTRODUCTIONCMP-10 is a compact, full featured portable line thermal printer, whichcan be used in a large variety of job environments rangin
— 11 —1.2 Included and Optional AccessoriesWhen unpacking the package, confirm the availability of:● Printer unit: 1 piece● Sample paper roll: 1 roll
— 12 —2. GENERAL SPECIFICATIONSFeature ParametersPrinting system Direct thermal printingPrinting speed 50 mm/secPrinting head Total dots: 384Dot dens
— 13 —Feature ParametersSerial interface Speed: 1200, 2400, 4800, 9600, 19200, 57600, 115200 bpsInterface: Bidirectional serial communicat
— 14 —Feature ParametersReliability Print head: 100,000,000 pulses or 50km(Normal temperature, 12.5% density, rated energy)Mechanism: 15,000,000 lines
— 15 —3.EXPLANATION OF PRINTER PARTS3.1 LED Indicators(1) Charge LEDRED on: Battery is chargingGREEN on: Battery is Fully charged(2) Power (Error) LE
We, the Responsible Party : CBM America Corporation363 Van Ness WaySuite 404Torrance, CA 90501, U.S.ATelephone (310) 781 1460declares that the product
— 16 —3.2 Communication Port and Switch(3) IrDA interface unitReceives data from host and transmits printer status.For communication with IrDA commun
— 17 —3.3 Inside of Paper Cover(10) Paper feed rollerFeeds paper through the printing mechanism.(11) Printing (thermal) headRecords print data on the
— 18 —(13)(12)(15)3.5 Bottom Surface and Battery Cover(12) Belt clipAttaches to the printer on your belt.(Not installed at the time of shipment. To u
— 19 —3.6 Dimensions and ViewsDC Jack(Unit: mm)
— 20 —4. OPERATION4.1 Replacing the Paper RollPress Cover Open switch (1).Open Paper Cover (2).Place the new paper roll as shown on illustration and
— 21 —4.2 Method of ChargingIf any of the following conditions occur, charging the battery is required.• “Low Battery” is printed.• The buzzer sounds
— 22 —4.3 Communication by IrDASet the infrared port of the device to face straight to the printer’s infraredport.Communication is available in the r
— 23 —4.4 Communication Via Serial Port (Cable)For communication with RS-232C, prepare dedicated serial cable.Open the serial port cover and while ho
— 24 —4.5 Reading Mag Stripe Card (Only Model with Built-in Mag Stripe Card Reader)To read the mag stripe card, it is necessary to send a special com
— 25 —4.6 Removing the Battery Pack1. Set the printer Power switch to OFF and unplug the AC adapter fromprinter.2. Remove the battery cover by (1) pr
FCC Compliance Statement for American UsersThis equipment has been tested and found to comply with the limits for a Class Bdigital device, pursuant to
— 26 —4.7 Installing the Battery Pack1. Insert the battery connector to the connector of the printer.2. Insert the battery connecting cable into the
— 27 —5. FUNCTION5.1 Auto Power OFFPower is automatically cut off after a specified period of time, duringwhich no command is sent to the printer an
— 28 —5.4 Monitoring the Print Head OverheatingIf the temperature exceeds 65°C for some reason, the printerautomatically stops printing with Power LE
— 29 —6. LIST OF COMMANDS1 BEL Sound the buzzer2 HT Horizontal tab command3 LF Printing and paper feed4 CR Print command5 ESC RS Sounds the buzzer6 E
— 30 —**34 ESC c5 Enabling/disabling the panel switches35 ESC d Printing and feeding the paper by n lines36 ESC v Transmitting the printer status37 ES
— 31 —7. MAINTENANCE AND SERVICEFor information on maintenance and service, please contact your CBMdealer or at the following addresses:Other AreasJa
— 32 —8. APPENDIXHANDLING BELT CLIP KITThis kit consists of a belt clip, two screws, and two rubber feet.8.1 How to Mount Belt ClipPeel off the cover
— 33 —MEMO
— 34 —MEMO
— 35 —MEMO
Manufacturer’s Name : Japan CBM CorporationManufacturer’s Address : CBM Bldg., 5-68-10, Nakano, Nakano-kuTokyo, 164-0001, JapanDeclaration on the Prod
Information Systems Division CBM Bldg., 5-68-10, Nakano, Nakano-ku,Tokyo 164-0001, JapanTel: (+81-3) 5345-7540 Fax: (+81-3) 5345-75410201E-0212 Prin
— 1 —GENERAL PRECAUTIONS● Before using this product, be sure to read through this manual. Afterhaving read this manual, keep it in a safe, readily ac
— 2 —SAFETY PRECAUTIONSAbout PictogramPrecautions and notices necessary to follow for preventing hazards to the user orother person or their propertie
— 3 —Precautions in Handling PrinterWARNING● If the product is kept in use under abnormal condition such asgeneration of heat, smoke, or abnormal odor
— 4 —● Do not touch the print head or paper cutter while replacing printpaper. Heated print head may cause burn. The cutter may causeinjury to the ha
— 5 —WARNINGDANGER● Entering battery liquid may result in loss of eyesight. Immediatelywash eyes with fresh water and get medical care.● Keep the fol
Comments to this Manuals