MOBILE THERMAL PRINTERMODEL CMP-10CMP-10BTUser’s Manual
— 8 —WARNINGCAUTIONCAUTION● With one side of the connector connected to this product, donot touch the metal part of the other connector.Precautions on
— 9 —THE TABLE OF CONTENTS1. INTRODUCTION ...111.1 Features ...
— 10 —6. LIST OF COMMANDS ... 337. MAINTENANCE AND SERVICE ...358. AP
— 11 —1. INTRODUCTIONCMP-10 is a compact, full featured portable line thermal printer, whichcan be used in a large variety of job environments rangin
— 12 —1.2 Included and Optional AccessoriesWhen unpacking the package, confirm the availability of:● Printer unit: 1 piece● Sample paper roll: 1 roll
— 13 —2. GENERAL SPECIFICATIONSFeature ParametersPrinting system Direct thermal printingPrinting speed 50 mm/secPrinting head Total dots: 384Dot dens
— 14 —Feature ParametersBluetooth interface Transfer method: Bluetooth 1.2 compliant(CMP-10BT only) Frequency: 2.4 GHzModulation method: FH method (Fr
— 15 —Feature ParametersPower supply monitoring Auto Power OFF (programmable - from 1 to 60 min.)Low battery monitoring included.AC adapter Model: 10A
— 16 —3.EXPLANATION OF PRINTER PARTS3.1 LED Indicators(1) Charge LEDRED on: Battery is chargingGREEN on: Battery is Fully charged(2) Power (Error) LE
— 17 —3.2 Communication Port and Switch(3) IrDA interface unitReceives data from host and transmits printer status.For communication with IrDA commun
This printer conforms to the following Standards:Low Voltage Directive 73/23/EEC, 93/68/EEC, EMC Directive 89/336/EEC,92/31/EEC, 93/68/EEC.LVD:EN60950
— 18 —3.3 Inside of Paper Cover(10) Paper feed rollerFeeds paper through the printing mechanism.(11) Printing (thermal) headRecords print data on the
— 19 —(13)(12)(15)3.5 Bottom Surface and Battery Cover(12) Belt clipAttaches to the printer on your belt.(Not installed at the time of shipment. To u
— 20 —3.6 Dimensions and Views(Unit: mm)DC Jack
— 21 —4. OPERATION4.1 Replacing the Paper RollPress Cover Open switch (1).Open Paper Cover (2).Place the new paper roll as shown on illustration and
— 22 —4.2 Method of ChargingIf any of the following conditions occur, charging the battery is required.•“Low Battery” is printed.• The buzzer sounds
— 23 —4.3 Communication by IrDAFor IrDA communication, DIP switch setting needs to be set for IrDA.Set the infrared port of the device to face straig
— 24 —4.4 Communication Via Serial Port (Cable)For communication via serial (RS-232C) interface, use Citizen CA10-01serial cable.When the printer is
— 25 —4.5 Communication by BluetoothFor the Bluetooth communication, it is necessary to choose CMP-10BTand set the DIP switches for Bluetooth.As buil
— 26 —4.7 Removing the Battery Pack1. Set the printer Power switch to OFF and unplug the AC adapterfrom printer.2. Remove the battery cover by (1) pr
— 27 —4.8 Installing the Battery Pack1. Insert the battery connector to the connector of the printer.2. Insert the battery connecting cable into the
— 1 —GENERAL PRECAUTIONS● Before using this product, be sure to read through this manual. Afterhaving read this manual, keep it in a safe, readily ac
— 28 —4.9 DIP Switch SettingEither Bluetooth or IrDA function of CMP-10BT have to be chosen byDIP switches.DIP switches are located under the battery
— 29 —4.10 Setup menu function (Firmware after Ver 2.20EN)Make sure the printer power is off. Press ON/OFF switch and keeppressed for about 5 seconds
— 30 — Top question items Additional questions YES (ON/OFF Switch) NO (LF Switch)CHANGE DISCOVERABILITY ? SET DISCOVERABILITY Discoverability ON Disc
— 31 —5. FUNCTION5.1 Auto Power OFFPower is automatically cut off after a specified period of time, duringwhich no command is sent to the printer an
— 32 —5.4 Monitoring the Print Head OverheatingIf the temperature exceeds 65°C for some reason, the printerautomatically stops printing with Power LE
— 33 —6. LIST OF COMMANDS1 BEL Sounds the Buzzer2HT Horizontal Tab Command3LF Printing and Paper Feed Command4CR Print one line Command5 ESC RS Sound
— 34 —***34 ESC a Aligning the characters35 ESC c5 Enabling/Disabling Panel Switches36 ESC d Printing and Feeding the paper by n lines37 ESC v Transmi
— 35 —7. MAINTENANCE AND SERVICEFor the information on maintenance and service, please contact ourdealer.
— 36 —8. APPENDIXHANDLING BELT CLIP KITThis kit consists of a belt clip, two screws, and two rubber feet.8.1 How to Mount Belt ClipMount the belt cli
— 37 —MEMO
— 2 —SAFETY PRECAUTIONSAbout PictogramPrecautions and notices necessary to follow for preventing hazards to the useror other person or their propertie
— 38 —WEEE MARK
2.10E-0612 Printed in Korea
— 3 —Precautions in Handling PrinterWARNING● If the product is kept in use under abnormal condition such asgeneration of heat, smoke, or abnormal odor
— 4 —● Do not touch the print head or paper cutter while replacingprint paper. Heated print head may cause burn. The cuttermay cause injury to the ha
— 5 —WARNINGDANGER● Entering battery liquid may result in loss of eyesight.Immediately wash eyes with fresh water and get medical care.● Keep the foll
— 6 —● Do not dip battery in water or sea water. Wet battery maygenerate heat or may be subject to corrosion.● Do not use or leave battery at high te
— 7 —CAUTION● Print density may change with the kind of print paper. Printdensity is adjusted by the Print Density Set command inCommand Reference.
Comments to this Manuals