LINE THERMAL PRINTER MODEL CT-S4000/CT-S4000DC User’s Manual
— 7 —Observe the following precautions for daily maintenance. When cleaning the printer, always turn it off and unplug it from thesupply outlet. Use
— 8 —THE TABLE OF CONTENTS1. GENERAL OUTLINE ... 91.1 Features ...
— 9 —1. GENERAL OUTLINEThe CT-S4000/4000DC are thermal line printers designed for use with a broadarray of terminal equipment including data, POS, an
— 10 —1.2 UnpackingWhen unpacking the printer, confirm that the following are provided:● Printer: 1● AC power cord : 1● User’s manual (This manual):
— 11 —1.4 Basic SpecificationsItem SpecificationsModel CT-S4000 PA, CT-S4000 RS, CT-S4000DC PA, CT-S4000DC RSPrint method Line thermal dot print me
— 12 —2. EXPLANATION OF PRINTER PARTS2.1 Printer AppearancePrinter coverPower switchOperation panelCover open buttonRear connector(Front view) (Rear
— 13 —● POWER LEDIlluminated when the printer power is on and off when the printer power isoff. May blink or light in a special mode or in case of fa
— 14 —2.2 Printer Cover Inside2.3 Other Built-in Functions● BuzzerThis printer has a built-in buzzer. It is operated in case of an error, operation
— 15 —3. PREPARATION3.1 Connecting the AC Power Cord1. Turn off the printer power switch.2. For AC power type (with built-in power supply), connect
— 16 —PrinterPin Signal2 TXD3RXD4RTS6 DSR7SG20 DTRPCSignal PinFG 1TXD 2RXD 3CTS 5DSR 6SG 7DTR 203.2 Connecting Interface CablesConfirm that the power
WEEE MARK,I\RXZDQWWRGLVSRVHWKLVSURGXFWGRQRWPL[ZLWKJHQHUDOKRXVHKROGZDVWH7KHUHLVDVHSDUDWHFROOHFWLRQV\VWHPVIRUXVHGHOHFWURQLFVSURG
— 17 —CAUTION!DO NOT connect any other device than the specified cash drawer to the cash drawerkick-out connector. (Also DO NOT connect a telephone li
— 18 —80mm 82.5mmScales→ Partition→ 3.4 Installing the PrinterThe printer can be installed horizontally, vertically, and on the wall.Vertical positio
— 19 —3.6 Setting DIP SwitchThe DIP switch is present on the serial interface board.Remove the board fixing screws, take out the interface board, and
— 20 —Sensor Position**1 φ21.0 φ18.0*2 φ24.5 φ21.53 φ28.0 φ25.54 φ31.5 φ28.05 φ35.0 φ32.0**5 φ21.0 φ18.0*4 φ24.5 φ21.53 φ28.0 φ25.52 φ31.5 φ28.01 φ35.
— 21 —4. MAINTENANCE AND TROUBLESHOOTING4.1 Setting/Replacing the paper roll4.2 Removing Jammed Paper1. Turn the printer power off.2. Open the prin
— 22 —4.3 Cleaning the Print Head1. Turn the printer power off.2. Open the printer cover.3. Wait several minutes. Wipe off any debris on the heating
— 23 —4.5 Hexadecimal Dump PrintingThis function is to print all received data in hexadecimal numbers. If problemssuch as missing data, data duplica
— 24 —● Black Mark detection error (in Black Mark mode)When Black Mark cannot be detected even if a certain amount of paper feedis carried out for Bla
— 25 —dD65~15044445.2 Printing PaperUse the print paper shown in the following table or the paper with equivalentquality.Paper Type Product NameRecomm
— 26 —Notes:*1: The factory setting of "Paper Select" will be different, depending on the model classfication.*2: In the case of selecting t
IMPORTANT: This equipment generates, uses, and can radiate radio frequency energyand if not installed and used in accordance with the instruction manu
— 27 —Switch No. Setting Default Set ValuesMemory SW7-1 Baud Rate 19200 bps/ 1200 bps, 2400 bps, 4800 bps, 9600 bps,9600 bps** 19200 bps, 38400 bps, 5
— 28 —2. Selecting memory switch (MEMORY SWITCH SELECT MODE)When the FEED button is pressed short (*1), printing occurs in the order of“Memory SW1” →
TA74902-00FX.XXE-0609Printed in Japan
— 1 —GENERAL PRECAUTIONS● Before using this product, be sure to read through this manual. After having readthis manual, keep it in a safe, readily ac
— 2 —SAFETY PRECAUTIONS ... WHICH SHOULD BE STRICTLY OBSERVEDBefore using this product for the first time, carefully read these SAFETY PRECAUTIONS.Imp
— 3 — Do not use or store this product in a place where it will be exposedto:* Flames or moist air.* Direct sunlight.* Hot airflow or radiation from
— 4 —Do not use the printer under the following conditions. A state subject to vibration or unstable state. A state with this product slanted.• Oth
— 5 —PRECAUTIONS IN HANDLING THE PRINTERPlease observe the following precautions for power source and powercord: Do not plug or unplug the power cord
— 6 —Caution label is attached on the position shown in the following figure. Carefullyread the precautions in handling before using the printer.THIS
Comments to this Manuals